Jump to content
Do Not Sell My Personal Information


Help! How To Fit Xenon Headlight Bulbs


w_ahmed_18
 Share

Recommended Posts

Hi guys,

I tried to fit some xenon bulbs I managed to get hold of today. But I couldn't do it because there was a metal clip surrounding the bulb and it wouldnt come out. Does anybody have any ideas on how to fit the bulbs as I am a newbie to all this?

Thanks.

Edit: The cars a Phase II Toyota Yaris - 1.3

Link to comment
Share on other sites


Welcome to TOC

You have found the difficulty in changing headlight bulbs :D There is not much room to change the bulbs on a Yaris, but it sounds like you have done the hardest bit in removing the rubber boot

The clip should be squeezed in at the ends and swung out of the way.

The bulb should then come out easily.........................do not touch the glass of the new bulb,......(or the old one) as you will shorten its life.

Best of luck..........let us know how you get on

Link to comment
Share on other sites

I just got ma dad to do them :D

What bulbs did u buy?

I bought H4 Philips Power 2 Night GT-150. Got free sidelights as well and they make a difference :thumbsup:

http://www.autobulbsdirect.co.uk/product.p...=255&page=1

+ there legal and they use the same wattage as the stock 1's which means u wont melt and plastic in the headlight :thumbsup:

BTW when my dad fitted the bulbs we discovered that my offside headlight adjuster motor runs permanently when the headlights are on

My dad phoned Toyota and it is a known fault. So its getting fixed under warrant but if it wasn't would cost somewhere in the region of £150 :o cause Toyota in there wisdom don't sell just a motor u need to buy and brand new headlight.

Has any1 else had/heard of this problem ?

Link to comment
Share on other sites

The bulbs are just a cheap pair and sidelights of eBay. Got them off a mate for free.

I tried to swing the clip out of the way, but still no luck. Even tried to remove with pliers but still didn't budge.

Has body got any further suggestions?

Thanks in advance

Link to comment
Share on other sites


You just pinch the ends, then clip should be able to move. Mess about with pliers and you'll proabably end up breaking them.

Link to comment
Share on other sites

You just pinch the ends, then clip should be able to move.

Thats what I told him this morning :rolleyes:

Link to comment
Share on other sites

this is based on the drivers side light, try to get pics if you need then just let me know.

the metal clip should be in 2 parts, the left clip push to the right and then towards the windscreen and the right clip push to the left and then towards the windscreen.

They clip in and the clip needs to be squashed to the side to unhook it, befor it comes loose.

if you need pics let me know and i'll do what I can

Link to comment
Share on other sites

I'm looking to upgrade my head lights when i look for them i only seee one type reccomended for me but i no there are 2 bulbs in each headlight to be changed?

What to do, what to do?

Link to comment
Share on other sites

there should be only 1 bulb in each headlight, 1 sidelight in each headlight and 1 indicator bulb.

unless you've got the new yaris then I couldn't tell you.

Link to comment
Share on other sites

sidlight? is that the first light you have when you turn the lights on at the first turn then second one is the other bulb above it, or is that the high beam? i've got a phase 2 Mk1 yaris

Link to comment
Share on other sites

Yes the sidelight is the one turn, then second turn is main beam, the main beam bulb also has a second filament in it which lights for full beam :thumbsup:

Hope that answers your question!

Link to comment
Share on other sites

2 mains, 2 sides yes. Tbh just upgrading the mains is good enough as the sidelights barely shed any light at all! However if you buy from certain sites, as recommended above, you get the sidelights free!

Link to comment
Share on other sites


I'm back and this time "i've got bulbs" except i can't fit them! I've done the sidelights but the main headlights is quick pokey to get to. How easy is it to remove the headlight itself? I kinda broke one the plastic clips holding the light but it doesn't seem to made a difference to how well the light is held in place. Any help or advice would be champion!!

Link to comment
Share on other sites

Cheers for that, i just really wanted to know whether u'd say you gotta remove....but now i know i just gotta do it with what i got its all good. I'll have a bash 2morro and tell all!

When i done a few more bits to my car i'll go gold and also post pics of my car.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share





×
×
  • Create New...




Forums


News


Membership