Jump to content
Do Not Sell My Personal Information


Recommended Posts

Had my car ages now and done a few mods so here is a build thread.

Car as i brought it - Standard.

19092009255.jpg

DSCF0002.jpg

Then came my private no plate and headlight eyebrows.

DSCF0003.jpg

Then my custom made induction kit.

22052010082.jpg

22052010079.jpg

Double din headunit and parrot kit.

Headunit10.jpg

Headunit11.jpg

Rubbed down and painted gear knob.

Gearcolour4.jpg

Painted VVTLI letters on engine bay.

26062010140.jpg

17" alloy wheels and lowered 35mm.

Feb.jpg

DSCF0003-1.jpg

Raised the rear of the bonnet.

DSC_0205.jpg

DSC_0206.jpg

New cat-back system.

DSCF0027.jpg

DSCF0026.jpg

DSCF0017.jpg

DSCF0045.jpg

DSCF0038.jpg

DSCF0037.jpg

DSCF0036.jpg

General pics.

DSCF5327.jpg

DSCF5324.jpg

I will get videos up of the new the exhaust soon.

Link to post
Share on other sites

  • Replies 62
  • Created
  • Last Reply

Top Posters In This Topic

Very nice mods so far mate :thumbsup:

Except the eyebrows are not my thing.

And uhm, sorry I ask, but isn't your exhaust tip hanging a little too much to the middle of the car? ;)

Grtz

Link to post
Share on other sites


I had a really productive day.

I cut my shifter down to reduce throw distance, it has worked.

First i removed the centre console out the car and removed the gear stick and housing.

In each corner there are rubber bushes.

DSC_0317.jpg

DSC_0316.jpg

Here they are out.

DSC_0318.jpg

Here is the shaft before i cut it.

DSC_0320.jpg

And how much i cut off.

DSC_0321.jpg

And the final result.

DSC_0323.jpg

I also adjust the handbrake while the centre console was out.

Link to post
Share on other sites
  • 2 weeks later...

Without wanting to mess up your thread, by cutting only the top of the gear stick you only achieve to make the gear changes more difficult. The speed of the gear change has not been altered at all.

The only "plus" of this mod is that the stick looks better as it is shorter.

Take a look at the TTE short shift stick that I have installed in comparison with the OEM one. Notice that the stick is shorter on the top but longer on the bottom (pic1).

Also, if you want to improve the "wavy" feeling of the tower that holds the stick, you need to replace also the rubber base bushings with aluminum ones (pic2).

tte1-1.jpg

tte2.jpg

All above are said in an entirely friendly way. I do not want to spoil your enthusiasm. Keep up the mods and good work.

Link to post
Share on other sites

Fair point on the tte shifter, but the twm short shifter is only shorter or the top compared to the standard shifter. Well that's how it looks so I could work.

Link to post
Share on other sites

By about 1mm, gear changes are not "more difficult" but more precise with less throw.

There is no wobble in mine as i took out the rubber bushings and bolted the gear selector bracket to the floor.

I havent re-threaded the gear stick yet but i do have my gear knob attachted securly for now.

Link to post
Share on other sites

It's not so simple mate. In order to achieve a shorter "throw" you must reduce the angle of throw!

By just cutting the top of the stick, you do not change the angle of throw. You just make the gear changes more difficult.

In order to achieve to reduce the angle of throw and thus achieve an actual shortening of the throw (and faster throw), the bottom of the stick must be extended and the stable part of the throw (i.e. the metal ball in the middle) to be displaced to a higher point.

I have prepared a rough sketch to explain...

short.jpg

The 1st stick is the OEM one. The 2nd stick is the one that you just cut the top. The 3rd stick is a proper short shifter.

As you have seen, in the 1st and 2nd stick the angle of throw remains exactly the same (30 degrees). In the 3rd stick the angle of throw has been reduced to 20 degrees.

The displacement of the metal ball is done by replacing the rubber base bushings with the aluminum ones. So their role is twofold. To stiffen the tower and to increase the height of it.

I am saying all above because I think it's not proper to advertise that by cutting off 50% of your stick, you achieve 50% reduction in throw... If only it was so simple...

Link to post
Share on other sites

your all right lol both ways will work. Shortening the shaft reduces the throw as there is less length to travel throuh and moving the ball wil change the fulcrum point reducing the throw that way. You just may need a weighted knob if you cut it down as you have less leverage force. The throw wil reduce more with a proper short shift but they cost and cutting it dont lol

Link to post
Share on other sites

ok maybe not 50% for 50% lol slight exageration. just measure the distance across the top of your first two drawings, the path is reduced quite a bit.

Yes, ok... I understood your exaggeration.

I just wanted to make clear that the important factor in this case is the angle of throw.

In any case, it is up to you or b1gpk etc, what you do with your car which is well respected.

I just expressed my opinion.

Hope you have the results you've expected and keep up the good work.

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.





×
×
  • Create New...