Jump to content
Do Not Sell My Personal Information


OriRacer

Advanced Members
  • Posts

    190
  • Joined

  • Last visited

Profile Information

  • Toyota Model
    AE102

OriRacer's Achievements

Collaborator

Collaborator (7/14)

  • First Post
  • Collaborator
  • Conversation Starter
  • Week One Done
  • One Month Later

Recent Badges

0

Reputation

  1. Hello all how are we all doing! I just got myself a ST185 up one of the headlights wont pop up. Anyone know where the screw is to wind them up manually?
  2. Is this something you have done as I've been advised not to do this!!?? dude if it fits put it on its only a air filter
  3. Only uk suppiler is fensport try ebay us importing stuff just now is really cheep since the dollar is ****
  4. The only thing you don't want to pull off is the toyota badge since its on pin's everything else should just be stick on's
  5. for the GXI Make - Toyota Model - Corolla >01 Year - 85 to 01 PCD - 4x100 Offset - 35 to 45 Bore - 54.1 I have alloy of a mk3 mr2 and the car is lowered by 40mm. The 15's at the front 'JUST' fit and 205 rubber catches on full lock. 16's on the back needed spacers to fit with out rubbing the struts. in a word NO they won't fit.
  6. As far as I remember NO 20v's dizzy and coil are the all in one type and some have coil packs.
  7. So how long before you hack it to bits like the rest of us :D
  8. yup it will fit but I would really go with a 20v gearbox.
  9. Late spec non tvis is the one to go for kicks out around 130bhp. If you were a mk1 mr2 owner same sort of body work will need done like the man says they rust like hell. should cost you around the £500-£1000 mark for one that wont need to much in its next MOT Just remember to give the sils and underneath a good going over before buying. But if it was me I'd trade the dog for a cat and get a 2 back instead
  10. Ok ppl timeeees up I've started listing items ebay userid is orignboy. I will be striping parts at my leisure now and most likely keeping half of them for my other projects :D so bid happy
  11. Bottom of the rad there is a little plastic wing nut. Shouldn't need to take off any panels.
  12. But before you start running around in it make note of the oil and coolant levels then give her some hard driving. Then monitor when cold over the next few days. If you see a noticeable drop in fluids then you MAY have a leaky head
  13. Do, if you get a response post it up. He mentions a belt conversion kit has been done. I'm sure you're aware that because of the longer 7A block the stock 4A-G belt won't fit on a 7A-G setup so maybe that's what he means by the belt conversion kit? I see there are no bids on it anyway. As Ecsy mentioned about needing new shells, it is unkown what damage may have been caused and this probably has deterred potential buyers. This is his reply to me its done from a 97 corolla engine the flywheel and crank are lightened with receipt, the pulley is a fensport 212 kit, conrods i dont know, the clutch was 350 pounds plus on its own I think it was done with a 4a block from a 4afe.... guy isn't very forth coming with pictures etc. as a few ppl have asked him.
  14. from the photo's although it's hard to tell the oil drain from the head to the block still looks to be there. This is not present on a 7A block so you block it off on the head when doing a 7AGE. Since this looks to be there I would guess its really a bored out 4A block. But if it was a 7AGZE with the custom conrod's I'd pay the 500 for that ;) Think I'll email him to see if he's full of ****.
×
×
  • Create New...




Forums


News


Membership