Jump to content
Do Not Sell My Personal Information


ilfdlab

Registered Member
  • Posts

    8
  • Joined

  • Last visited

Profile Information

  • Gender*
    Male
  • Toyota Model
    O4 Avensis 1.6
  • Location
    Dublin

ilfdlab's Achievements

Rookie

Rookie (2/14)

  • First Post
  • Conversation Starter
  • Week One Done
  • One Month Later
  • One Year In

Recent Badges

0

Reputation

  1. Hi all, just wondering if anybody would have front seats for a 2004 Corolla T-sport face lift ? The seats fitted are black with red trim ? I've checked eBay but none if the sellers ship to Ireland. Thanks in advance.
  2. ilfdlab

    Avensis

    Hi t-spiritpete, I've to replace my 2004 Avensis saloon 1.6 petrol clutch & my wifes 2002 Corolla 1.4 VVTI 4 door clutch - expensive after Christmas. Just wondering if these downloads are basically the same for the 1.6 Avensis & 1.4 Corolla ? Is there anything to watch out for while c/o the job ? Thanks in advance.
  3. This worked for me http://boards.ie/vbulletin/showthread.php?...ighlight=toyota hope it's of help to you ;)
  4. Sounds like you could be buying into trouble, saw this on adverts.ie - might be of interest ? Money seems ok for the year & condition. http://www.adverts.ie/showproduct.php?prod...507&cat=all
  5. Just lubed my clutch with light grease & silicone spray, all seems nice & quiet now we'll see how it gets on.
  6. Hi Fitter, thank you for your reply ! I used the following (B. Rewrite mode) but will try your method (which looks nice & quick) with the spare key : There are four different programming commands when setting up or verifying your remote transmitter, they are: A. Add mode, used to add a remote to your Prius that is not currently registered. B. Rewrite mode, used to erase all previously registered remotes and allow you to begin again the programming process. C. Confirmation mode, used to verify the number of remotes that are already programmed in your Prius. D. Prohibit mode, to prohibit all remotes from operating the door locks. All four modes start with these instructions: 1) Make sure that the key is not in the ignition, the doors are unlocked, and the driver's door is open. 2) Very quickly, without turning, insert and remove key from the ignition twice. (leave key out) 3) Close and open the driver door twice. (leave door in open position) 4) Again, insert key into the ignition and remove it. This time only once. (leave key out) 5) Close and open the driver door twice, then close the door. 6) Insert key into the ignition and leave it in the LOCK position. A. Add mode: A1) Turn the key to "ON" for 1 second, then turn back to "LOCK". A2) Remove the key. A3) You’ll hear the doors "LOCK" and 1 second later "UNLOCK" (just listen) A4) On your remote, press the lock and unlock buttons simultaneously for 1 to 1½ seconds, then let go. A5) On your remote, IMMEDIATELY press unlock by itself. A6) You’ll get one of three responses: R1) You’ll hear the doors "LOCK", then "UNLOCK" once. The remote is accepted. If you want to program another remote, immediately proceed to step A4 with your second remote, otherwise open the driver’s door and the remote is registered. R2) You’ll hear the doors "LOCK", then "UNLOCK" twice. Either you didn’t use the same remote in steps A4 and A5(not likely), or this remote was already registered. The timing was off when you pressed the LOCK and UNLOCK buttons simultaneously and then UNLOCK by itself. Immediately press the two buttons together and the unlock by itself again. Keep trying until you get the locks to signal once that you have been successful. Then if you have another remote to program, quickly press its' buttons as before, until you hear the locks signal once. When you are finished, open and close the driver door to lock in the programming. R3) If no response, go back to step 1 near the beginning of these instructions. B. Rewrite mode: B1) Turn the key to "ON" for 1 second, turn back to "LOCK" for 1 second, then back to "ON" for 1 second, and finally back to "LOCK" for 1 second B2) Remove the key. B3) You’ll hear the doors "LOCK", 1 second later "UNLOCK", 1 sec., "LOCK", 1 sec. "UNLOCK". (just listen) B4) On your remote, press the lock and unlock buttons simultaneously for 1 to 1½ seconds, then let go. B5) On your remote, IMMEDIATELY press unlock by itself. B6) You’ll get one of three responses: R1) You’ll hear the doors "LOCK", then "UNLOCK" once. The remote is accepted. If you want to program another remote, immediately proceed to step B4, otherwise open the driver’s door and the remote is registered. R2) You’ll hear the doors "LOCK", then "UNLOCK" twice. You didn’t use the same remote in steps B4 and B5(not likely). R3) If no response, go back to step 1 near the beginning of these instructions. C. Confirmation mode: C1) Turn the key in 1 to "ON" and back to "LOCK" in one second intervals for a total of 3 times. C2) Remove the key. C3) You’ll hear the doors "LOCK" and "UNLOCK" in 2 second intervals. (just listen and count each set) 1 Set = You have 1 remote registered 2 Sets = You have 2 remotes registered 3 Sets = You have 3 remotes registered 4 Sets = You have 4 remotes registered 5 Sets = You do NOT have any remotes registered D. Prohibit mode: D1) Turn the key to "ON" and back to "LOCK" in one second intervals a total of 5 times. D2) Remove the key. D3) You’ll hear the doors "LOCK", 1 second later "UNLOCK" 5 times. (just listen and count each set) D4) This will erase all previously registered remotes and cancel the wireless door lock function.
  7. I'm in trouble too with this, I've changed the battery but it won't lock/unlock now....red light is flashing on the key but nothing happens....
  8. Hi all, my 97 1.6 Carina with the 4A-FE engine is suffering from the dreaded injector problem as discussed in other posts. Could anybody advise the part numbers for the injectors so I can start searching for replacements ? Thanks in advance.
×
×
  • Create New...




Forums


News


Membership